What are the Common Problems with Vokera Boilers?

Troubleshooting Vokera Boiler Faults

Are you wondering what are the common problems with Vokera boilers?

Most Vokera faults boil down to one of two problems: an A01 ignition failure, gas supply, frozen condensate, or worn probe, or an A04/AL40 pressure drop below 1.0 bar. These are the codes most likely flashing on your display.

We have pulled apart enough Vokera Mynute, Easi-Heat Plus, Vision Plus, Compact A, and Evolve units to know that the fault code on the screen is only the starting point. The manual gives you the symptom. What matters is what we find when we open the casing, and that is what this guide covers.

Ignition Failure (A01): The Real-World Causes

The A01 fault codes ignition failure, and the manual is quick to point at the gas valve or the ignition electrodes. On site, though, the picture is usually more specific: in winter, a frozen condensate pipe backing up into the boiler is the most common cause we encounter.

When the condensate has nowhere to go, the boiler locks out to protect itself. The probe might be perfectly serviceable and the gas valve fine, but the blockage stops the cycle before it starts. Other causes we check:

  • Gas supply interrupted or the isolation valve left closed after a service
  • Worn ignition probe; the electrode tip degrades and the spark can’t bridge
  • Faulty gas valve that fails to open on command

Testing the ignition lead with a multimeter gives you a real answer rather than swapping parts on guesswork. Check continuity across the lead from the PCB to the electrode; a break there mimics a dead probe every time.

If you are on the phone with your homeowner and the condensate is the suspect, thaw it carefully with warm, not boiling, water and reset. If the fault returns, you are looking at a deeper issue and it is time to book an emergency gas engineer call-out.

Constant Pressure Drops (A04 & AL40)

The A04 and AL40 faults both flag the same problem: system pressure has dropped below 1.0 bar. On the Vokera Compact and Easi-Heat Plus, that threshold trips the lockout before you even notice the pressure gauge.

To repressurize your heating system, open the filling loop’s isolating valve and the connector tap at the other end, then watch the gauge climb. Close both valves once you hit 1.3 to 1.5 bar, then reset the boiler. If the pressure holds, you were likely dealing with a small radiator leak or air that needed bleeding.

Here is the engineering reality, though: if the pressure drops constantly and you are topping up every few weeks, a loose pipe is not your problem. You are almost certainly looking at a flattened expansion vessel that can no longer absorb the water’s thermal expansion, or a pressure relief valve (PRV) letting by. Both need a proper diagnosis, not another top-up.

Fan Faults (A03) and Diverter Valve Leaks

The A03 code flags a fan or tacho signal failure. The fan has stopped spinning, the tacho sensor is not reporting back, or moisture has got into the fan electricals and the board is reading a fault that may not exist. A blocked flue can also starve the fan of airflow and trigger the same code, so check the flue terminal before pulling the fan.

On Vokera units, though, there is a trade pattern worth knowing: the diverter valve is prone to weeping water directly onto the microswitch and the PCB underneath. That moisture creeps into terminals and traces, throwing up cascade electrical failures that look on the surface like a dead fan or a sensor fault. By the time the A03 is showing, the diverter valve may have already damaged the board it sits on.

If the fault keeps coming back after the fan and flue are ruled out, the diverter valve and PCB need a proper look. Book professional boiler diagnostics before chasing components that may not be at fault.

Repair vs. Replace: The Vokera Economics

If you are weighing up a repair on a Vokera Compact or Easi-Heat, be honest about the numbers. These are budget-friendly boilers by design, and that means the parts are priced accordingly, but the labour on top still adds up fast. When a call-out, a new PCB, and a fan motor are heading past £300, the repair is no longer the obvious call. At that point, upgrading to a new unit with a fresh warranty usually makes more financial sense than sinking money into ageing components. If the diagnosis is pointing that way, get in touch and we will start quoting for a replacement boiler rather than patching something past its best.

Frequently Asked Questions

How do I fix a Vokera A04 error code?

The A04 or AL40 error indicates low system water pressure. To fix this, locate the external filling loop beneath the boiler and open the valves until the pressure gauge reads between 1.0 and 1.5 bar, then reset the boiler.

Why does my Vokera boiler show an A01 fault?

An A01 fault means ignition failure. While this can be a faulty gas valve or ignition probe, the most common cause during winter is a frozen condensate pipe that has backed up and drowned the spark.

What does a flashing red light on a Vokera boiler mean?

A flashing red light indicates a safety lockout. This is typically accompanied by a fault code on the digital display, such as A02 for overheating or A03 for a fan fault, requiring a Gas Safe engineer to diagnose.